top of page

Chiller

  • While an upgraded chiller is recommended to be added at time of purchase, it is not required. This should however, be considered an item to be purchased at a later date.

  • The laser tube will get hot during operation. It is necessary to keep the tube cool to prevent damage to your laser tube. In fact the machines are setup to not fire the laser if there is no flow of water through the laser tube. Excessive heat will shorten the life of your laser tube. 

  • All machines come with an and aquarium style pump which can be placed in a bucket or similar container containing distilled water.

    • These pumps do work well but also require your attention.

    • It is important to make certain, especially when doing long engraves or cuts, that your water does not get to warm.

    • Ice packs, frozen water bottles, etc. can be placed in the bucket to keep the water cool. This method does work but can be especially troublesome for those who use their machine in warmer environments. It also does not provide a constant temperature.

  • There is an additional expense if opting to buy a chiller when purchasing a machine. However, it is likely that this additional equipment will save you money in the long run by helping to extend the life of your laser tube.

  • While it is preferred to keep your laser in climate controlled environments, those who do plan to use their laser in a colder environments (ex. unheated garage or shed in northern states) may want to consider a chiller which has a built in heater for times when ambient temperatures can get below freezing.  The laser tube is glass, so freezing water will break the tube. In this case check out the LightObject chiller below which comes with a built in heater. While I do not recommend many users suggest to use RV anti-freeze in the event you have a loss of power this can act as a backup to help prevent freezing. 

Chiller Information

Suitable for one (1)  CO2 laser ranging from 50W - 150W

  • 22” x 11.4” x 17” (56 x 29 x 43 cm) overall dimensions

  • 57.3 lb. (26 kg) overall weight

  • Spacious yet compact 1.6 gallon (6 L) tank

Monport CW-5200

Monportwaterchillershow_750x.webp

Select Retailer to purchase

Monport Chillers
OMTech Chillers
S&A Chillers

S&A CW-5000

Suitable for one (1)  CO2 laser up to 100W

  • 22.83" x 11.5" x 18.5"  (58 cm x 29 cm x 47 cm) overall dimensions

  • 64 lbs (29 kg)

  • 1.85 gallon (7L) tank

S&A CW-5200

Suitable for one (1)  CO2 laser ranging from 50W - 150W

  • 22.83" x 11.5" x 18.5"  (58 cm x 29 cm x 47 cm) overall dimensions

  • 64 lbs (29 kg)

  • 1.85 gallon (7L) tank

S&A CW-5202

Suitable for one (1) or two (2)  CO2 lasers ranging from 50W - 150W

  • 22.83" x 11.5" x 18.5"  (58 cm x 29 cm x 47 cm) overall dimensions

  • 64 lbs (29 kg)

  • 1.85 gallon (7L) tank

S&A Chillers
LightObject Chillers
Save 5% on all items from LightObject.com with Coupon Code: OEADESIGN

Water Heater After Burner

Fully automated and programmable water heater with built-in water flow rate monitor

  • Flow meter, Gal/min or L/min

  • Temperature sensor 

  • Temp. control - start temp/shut off temp from 0'C ~ 40'C

  • Alarm - adjustable over-heated alarm

  • Protection - Low flow protection. 

After-Burner-860__69294.1642620758.jpg
LightObject Chillers

Chiller Setup

  • Monport Chiller manuals can be downloaded by clicking on the correct model number below

    • CW-​5200
       

  • S&A Chiller manuals can be downloaded by clicking on the correct model number below

Disclaimers:

I do not make any warranties, neither expressed nor implied, about the accuracy, completeness or reliability of the information contained in this website. The above information is provided based upon the best of my knowledge. Any use of the information on this web site is strictly at your own risk. I will not, nor cannot, be held liable for any damages or otherwise in connection with the use of the information contained on this web site . Use of this web site indicates understanding and acceptance of this statement and releases me from any and all liability. The information above is subject to change at any time.

 

As an Amazon Associate I earn a commission from each qualifying purchase. As an affiliate for OMTech, Monport, SpetTols, Microjig and other affiliate programs, I earn a commission from each qualified purchase.(C) 2021-2022  M. Arnio. All rights reserved. No parts of the content of this website may be reproduced or distributed in any way, without prior written permission. All trademarks, service marks, images, and company names are the property of their respective owners.

bottom of page